Switch Pro Quick Connect Harness for ARB Air Compressor SP-ARBH
Quick Connect Harness for ARB Compressors (all models).
ARB Compressor Mount Bed Side Toyota Tacoma - BCM0001EX
The first of its kind; a concealed and easily accessed compressor mount for the 2nd and 3rd Generation Toyota Tacoma 2007-2019
Mounts in place of the factory driver or passenger side rear storage box in the bed. Solid, secure and convenient. Facilitates re-installation of factory box lid after easy modification (trimming) of the lid flange and removal of the box.
Manufactured from 5052 .125 Aluminum and powder coated for superior corrosion resistance.
Includes mounting hardware for mount to vehicle
Mounting instructions included
Install time approx 1.0 Hrs excluding wiring of compressor
Holds both ARB Twin/Single, Viair and Smittybuilt Compressors
**Note- if installing a Viair or Smittybuilt compressor drilling is required in bottom tray for installation.
***This listing is for the Expeditions Essentials Compressor Mount ONLY. Compressor and lines must be purchased separately.
10-Present Tacoma OEM Fit Toyota Tacoma Air Compressor Kit
Take the guesswork out of maintaining proper tire air pressure with the Cali Raised Offroad on board Air Compressor Kit. It can be used to reinflate tires after deflating them for off-road adventures or to top off tires when the Tire Pressure Monitor (TPM) indicates low tire pressure. This integrated onboard compressor can also be used to inflate air mattresses, soccer balls, footballs, basketballs, bicycle tires and pool floats.
This OEM Fit Toyota Tacoma On Board Air Compressor uses a Single 12V Compressor capable of filling a tire at a rate of 2.54 CFM.
It mounts under the Rear Seats and comes with a harness that runs to the battery.
No Load Current Draw
Under Load Current Draw
33% @ 100PSI
Max Working Pressure
No Load Air Flow
2.54 CFM @ 0PSI
Loaded Air Flow
1.60 CFM @ 40 PSI
Average Inflation Time:
Tacoma 33" Tire from 15 PSI to 35 PSI
ARB Inflation Accessory Kit - 171302
ARB's optional tire pump up kit is a must have for any trail rig. Makes it way too easy for airing those tires back up after a day of wheeling. Also includes attachments for airing up football, soccer ball, volley ball, or air mattress,
Kit Contents: High Heat Tolerant 20' Poly Air Hose T-Fitting Quick Disconnect Locking Tire Chuck Needle for balls Attachments for airing up air mattresses/floaties
Optional pump up kit allowing you to use your CKMA12 Compressor and the new CKMTA12 and CKMTA24 TWIN compressors to quickly plug in a heavy duty airline and air up tires after a day on the trail or fill up after patching a flat tire.
Due to the incredible air-output produced from the Hi-Output CKMA12 compressor and the CKMTA12 and CKMTA24, this air compressor requires a unique, high-heat tolerant 20 ft hose, specially sourced from Japan. Designed by ARB engineers for maximum air flow this Tire Inflation Kit also includes a dust free quick release air chuck, which boasts an enclosed internal bearing system to prevent dirt ingestion. Air up quickly with the ARB Tire Inflation Kit!
The nice thing about this hose is that it has line protectors on the end, which helps from kinking, and makes the hose last a long time.
ARB On-Board Twin High Performance 12 Volt Air Compressor - CKMTA12
ARB MAXIMUM OUTPUT ON-BOARD COMPRESSOR
Providing optimum power, the ARB twin motor design delivers class-leading air flow for fast inflation purposes. Constructed of lightweight, high-strength engineering grade materials, it incorporates quality components for quiet operation and extended durability. The twin motors incorporate internal thermal protection against extreme temperature damage while a heavy duty in-line maxi fuse for each motor provides professional circuit protection. Available as either a portable kit with a 4L air tank, inflation accessories and a durable carry case or a vehicle mounted kit with associated wiring loom and mounting hardware.
Pneumatic supply and electrical control for ARB Air Locker (Air Locker Manifold Kit #171503 required)
Rapid inflation of small, medium and large tires
100% duty cycle
Sealed for moisture and dust resistance
Air tools rated up to 85LPM [3CFM] @ 6Bar [90PSI] continuous supply
Air tools rated higher than 85LPM [3CFM] @ 6Bar [90PSI] using an optional air tank suitable to the run time requirements
Fully assembled and tested air compressor (12V)
Complete wiring loom with Air Locker solenoid plug-in terminals
ARB BEDSIDE COMPRESSOR MOUNT EXTENSION HARNESS by Expedition Essentials
Take the guesswork out of installing your Bedside Compressor Mount with ARB Twin Compressor: with our new Extension Harness.
This 15' harness will enable you to install your on board air in the bed of your vehicle with room to spare.
Using ARB's exact specs for their supplied harness and stepping it up a notch with higher temp rated wiring. Identical connectors to ARB for a plug and play installation.
Finish your compressor install with ARB's supplied harness under the hood as intended.
Compatible with ARB Twin Compressor ONLY
This is for the HARNESS ONLY.. Air compressor and tray sold separately
Pneumatic Air Toggle Switches For Air Lockers 6MM Power Tank - ARB-2060-6
If you're like most offroad competitors, you'd rather have the simplicity and reliability of a total pneumatic air locker system. These air toggles include push-in compression fittings made to fit the ARB airline, so hook up is a breeze. Note: ARB has recently switched from a 5mm line to a 6mm hose. Please check to see the hose size of your ARB kit to ensure a proper fit with the Power Tank components.
The switch has a bulkhead fitting for a clean and easy installation. You can purchase a single switch or a pair of switches. If you are buying as a pair for a front and rear locker, one switch will have a split output to the other switch, so you only have to run one line from your air source.
Pair your switches with a pressure release valve assembly (ARB-0120) for a comfortable, complete solution to running your air lockers off of a Power Tank.
ARB Pressure Release Valve 150 PSI Power Tank - ARB-2000
150 psi Pressure Release Valve for ARB Lockers. No matter what kind of air system you make or buy to run your ARBs you absolutely have to have an in-line pressure relase (150psi) to protect your ARB seals. In case of pressure surge this will save your ARB.
With this piece installed in your system, if pressure ever spikes or goes above 150 psi, the spring will compress and release any excess pressure. This is not a one-time-use component and should last years.
1/4 inch NPT Male Threads
'-3An Adapter Fittings For Steel Line Arb Install With Power Tank - ARB-8NPT
When replacing your blue 5mm or 6mm ARB air line with steel line with -3AN ends, you need an adapter.
The 1/8" NPT adapter is what you need at your regulator outlet port, your pneumatic toggle switches, or in a standard air manifold with pipe thread ports.
Get it installed
Cali Raised Offroad can install your vehicle goodies with professional clean factory look.